Iphone 6 Display Und Homebutton Austauschen

Introduction

Use this guide to remove or replace the habitation push button in your iPhone 6.

Delight note that merely the phone'southward original home button assembly will be capable of using the Touch ID functionality. Installing a new abode button will only restore ordinary home button functions, non the Touch on ID features.

You can also use this guide to supervene upon the following parts:

• Front end Console Assembly Cable Bracket
• Home Button Bracket

Video Overview

• Before disassembling your iPhone, belch the battery beneath 25%. A charged lithium-ion battery can take hold of fire and/or explode if accidentally punctured.

• Power off your iPhone before beginning disassembly.

• Remove the 2 3.half dozen mm-long P2 Pentalobe screws next to the Lightning connector.



• The next three steps demonstrate using the iSclack, a peachy tool for safely opening the iPhone half-dozen that we recommend for anyone doing more than one repair. If you lot aren't using the iSclack, skip down three steps for an alternate method.

• If the plastic depth gauge is attached at the centre of the iSclack, remove it now—it'due south not needed for larger phones similar the iPhone 6.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in betwixt the suction cups.

• Position the iSclack'south upper suction cup against the brandish, but to a higher place (but not roofing) the home button.

• Open the handles to shut the jaws of the iSclack. Middle the suction cups and press them firmly onto the peak and bottom of the iPhone.

• If your display or dorsum glass is desperately croaky, covering information technology with a layer of clear packing record may help the suction cups attach. The iSclack also includes two pieces of tape for this purpose.

• Hold onto your iPhone deeply and close the handle of the iSclack to divide the suction cups, pulling the front panel up from the rear case.

• The iSclack is designed to safely open up your iPhone only enough to divide the pieces, but not plenty to damage the display cables.

• Peel the 2 suction cups off your iPhone.

• Skip the next three steps and continue on to Step 8.

• If you don't have an iSclack, use a single suction loving cup to elevator the front panel:

• Press a suction cup onto the screen, just to a higher place the dwelling house button.

• Be sure the cup is pressed securely onto the screen to go a tight seal.

• If your display is desperately cracked, covering information technology with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very potent tape may exist used instead of the suction loving cup. If all else fails, you can superglue the suction cup to the broken screen.

• While holding the iPhone downward with one hand, pull up on the suction cup to slightly split the front panel assembly from the rear case.

• Take your fourth dimension and apply firm, constant strength. The brandish assembly is a much tighter fit than most devices.

• Using a plastic opening tool, begin to gently pry the rear example down, away from the display assembly, while continuing to pull up with the suction cup.

• There are several clips holding the forepart panel assembly to the rear instance, so yous may demand to utilize a combination of the suction loving cup and plastic opening tool to costless the front panel assembly.

• Pull the plastic nub to release the vacuum seal on the suction cup.

• Remove the suction loving cup from the display assembly.

• Open the iPhone by swinging the dwelling button end of the front console assembly away from the rear case, using the superlative of the phone every bit a hinge.

• Several clips along the pinnacle edge of the forepart panel form a partial hinge.

• During reassembly, align the clips just below the top edge of the rear case. Then, slide the front console upward until its top edge is flush with that of the rear case.

• Open the brandish to about a 90º angle, and lean it against something to continue information technology propped upward while you're working on the phone.

• In a pinch, an unopened canned drink works well for this.

• Add together a rubber band to go along the display securely in place while you lot work. This prevents undue strain on the brandish cables.

• Remove the post-obit Phillips screws from the battery connector bracket:

• One 2.two mm screw

• One 3.2 mm screw

• During your repair, continue track of each screw and make sure it goes back exactly where it came from to avert dissentious your telephone.

• Remove the metallic battery connector bracket from the iPhone.

• Apply a plastic opening tool to gently pry the bombardment connector up from its socket on the logic board.

• Take care to but pry upwardly on the battery connector, and not the socket on the logic board. If yous pry upwardly on the logic board socket, you may suspension the connector entirely.

• Remove the following v Phillips screws securing the front panel assembly cable bracket:

• Three 1.2 mm screws

• One 1.vii mm screw

• 1 3.one mm screw

• Incorrect placement of these screws during reassembly will cause permanent harm to your iPhone's logic lath.

• Remove the forepart panel assembly cable subclass from the logic board.

• In the next four steps, have care to pry upwards but on the cable connectors, and not on their sockets on the logic board.

• Use a spudger or a fingernail to disconnect the front-facing camera and sensor cable connector.

• Use a spudger or a fingernail to disconnect the home push button cable connector.

• Make sure the battery is disconnected before y'all disconnect or reconnect the cable in this step.

• Use a spudger or a fingernail to disconnect the display data cable connector.

• When reassembling your phone, the brandish information cable may pop off its connector. This can result in white lines or a blank screen when powering your telephone dorsum on. If that happens, simply reconnect the cable and power cycle your telephone. The best mode to power cycle your phone is to disconnect and reconnect the battery connector.

• Utilize the apartment end of a spudger to disconnect the digitizer cable connector.

• When reconnecting the digitizer cablevision, exercise not press the middle of the connector. Printing 1 end of the connector, so press the opposite end. Pressing in the center of the connector can bend the component and crusade digitizer damage.

• Remove the front panel assembly from the rear case.

• Remove the ii one.9 mm Phillips screws securing the home button bracket.

• Remove the home push button bracket from the front panel.

• Utilize the point of a spudger to disconnect the home button cable connector past pushing it upwards and away from the home button.

• The rubber membrane surrounding the home push button is very thin and tears easily.

• Employ mild heat (with an iOpener, heat gun, or pilus dryer) to soften the adhesive securing the abode button membrane.

• Using your fingertip, apply business firm, constant pressure level on the home button from the front side of the brandish assembly, until the membrane starts to separate from the front panel.

• Do not push the home button all the way through—you but need to get a corner gratis and so that you can pry it free with a spudger.

• Peel the abode button the rest of the way off of the display by prying gently with a spudger.

• Employ the betoken of a spudger to carefully split the habitation push button cable from the agglutinative securing it to the front panel.

• If the cablevision doesn't separate easily, employ estrus using an iOpener or hair dryer to soften the adhesive, and endeavor again. Exist careful not to damage the cable.

• Once all the adhesive has been separated, remove the home button from the front end panel.

• If you are replacing a broken front panel, there may be glass shards stuck to the home push. Carefully remove whatever remaining glass before transferring your home push to a new display.

• Your replacement role may come with an extra Phillips spiral already installed left of the Home Button. Remove the unnecessary screw and so that you can reinstall the home push bracket.

• Depending on your replacement part, you may need to remove the condom gasket effectually your home push button.

• Employ a prepare of tweezers to advisedly pull the gasket up from the home button.

• Be careful non to snag the gasket on the dwelling house button cable.

Conclusion

To reassemble your device, follow these instructions in reverse social club.

Team

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+6+Home+Button+Replacement/31935

Posted by: joneswakepten.blogspot.com

Share this post